Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Garland Homeowners Choose Toto Construction
We provide independent Toto construction service in Garland, TX: installation, repair, and full bathroom work built around Toto’s washlet seats, dual-flush valves, and one-piece skirted traps. What makes our Toto work different is familiarity. Our independent local pros handle these fixtures regularly and know which failures are a quick component swap and which mean replacement. We are an independent service provider, not a Toto dealer and not authorized or certified by the manufacturer. If your Washlet stopped heating, or a Toto toilet keeps running, the fastest answer is a conversation. Our technicians have up to 10 years of experience. Call (888) 405-7616. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Construction Garland for Your Toto Construction?
Toto fixtures sit at the higher end of bathroom equipment, and they fail in specific ways: electronic bidet seats that quit spraying or warming, fill valves and flappers that wear on Drake and Ultramax tanks, and gasket seepage at one-piece skirted traps. A general plumber meets these rarely. Our technicians have up to 10 years of experience working with them and treat the electronics as their own discipline, not a footnote on a toilet call.
Parts make or break the job. Where genuine Toto fill valves, flappers, and washlet components exist, we use them. For discontinued items, we source reputable aftermarket parts that fit properly rather than forcing a part that half-works. That distinction matters in a Garland bathroom, where a cheap flapper that seats wrong turns into a running tank and a higher water bill within weeks.
We also keep the work warranty-safe: we diagnose the actual failed component instead of swapping whole assemblies, and we document what was replaced so the service record stays clean for the fixture you own. We’re independent, so our recommendation is about your fixture, not about moving inventory.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in Garland
These are the failures we see most on Toto equipment in Garland homes, and the reasons behind them.
- Washlet seat stops spraying or heating. The pump, heating element, or control board has failed. Electronic bidet seats live in a humid bathroom, and moisture plus years of use wear on the board and pump. Sometimes it’s one component. Sometimes the board replacement costs more than a new seat, and we’ll say so plainly.
- Drake and Ultramax tanks running after a flush. The fill valve or flapper has worn and no longer seals, so water trickles continuously and the tank refills itself. It’s quiet, easy to miss, and shows up as a rising water bill. These are inexpensive parts and a quick fix once identified.
- Gasket and seal leaks at the skirted trapway or tank-to-bowl joint. One-piece Ultramax and similar units hide their plumbing behind a skirt. When a gasket fails, the leak shows up as moisture at the base or a faint smell, not an obvious puddle. Tearing down a one-piece assembly takes more precision than a two-piece, and that’s the work we do.
- Wax ring and flange failure under heavy one-piece bowls. A one-piece Toto bowl carries real weight, and an aging flange or compressed wax ring lets it seep slowly at the floor. Soft flooring or a loose toilet is the warning. Left alone, it rots the subfloor.
- Dual-flush valve and handle issues. High-efficiency models use valve mechanisms that wear differently than a standard flapper. A handle that needs two or three presses, or a flush that runs weak, usually points at the valve assembly, not the water supply.
Toto Parts & Our Repair-vs-Replace Approach
Our rule is simple: repair when the repair genuinely pencils out, replace when it doesn’t. We use genuine Toto fill valves, flappers, and washlet components where they exist, and reputable aftermarket parts only for discontinued items. We don’t claim to stock OEM parts or hold dealer inventory. We source what fits, and we tell you what we’re using before we install it.
For washlets, the math is often close. A failed control board on an older integrated seat can cost nearly as much as a replacement seat, and chasing a dying board rarely pays. For a Drake or Ultramax, a fill valve, flapper, or gasket swap is almost always the right call over replacing the fixture. The toilet itself is usually sound; the wear parts aren’t.
If you’re unsure which side of that line your fixture sits on, call (888) 405-7616 for a free estimate and we’ll walk you through it.
Our Toto Service Process – Step by Step
- 1
Diagnosis. We test the fixture directly: does the Washlet spray, heat, and respond to controls; does the tank seal; is there moisture at the trapway or floor. Electronics get checked at the seat and at the supply. No assumptions from a symptom alone.
- 2
Repair or install. Once we know the failed component, we set the part and the price in a written estimate before work starts. For a replacement, we match the new Toto unit to your rough-in, flange, and supply so it seats correctly the first time.
- 3
Test. We run a full flush cycle, test every washlet function, and check the base and joints for any seepage. A running tank or a cold seat doesn’t leave the room.
- 4
Warranty and record. We document the components replaced, which keeps your service record clean for the fixture and makes any later warranty question straightforward to answer.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in Garland
We work on the Toto products that dominate Garland bathrooms. That includes Drake and Drake II two-piece toilets (the CST743 and CST454 series), Ultramax and Ultramax II one-piece units, and the Washlet electronic bidet seats (S350e, C200, K300). We also service EcoPower and EcoPromenade high-efficiency models, where the flush valve assembly and electronic components each wear on their own schedule. Installation, repair, and component replacement all fall inside our bathroom scope, alongside the remodel work that surrounds them: small bathroom remodels, vanity installation, and tile and fixture work.
We Also Service These Brands
Toto is one brand of many we handle. We also service Kohler plumbing fixtures, KraftMaid cabinetry, and Cambria and Silestone countertops, so a bathroom or kitchen project can be specified and executed across brands in one place. If your room combines a Toto toilet with a Kohler vanity faucet and a Cambria top, you’re not juggling three contractors. You’re talking to one team.
FAQs – Toto Construction Service in Garland
Almost never. The toilet bowl and tank are usually fine; the failure is inside the Washlet seat itself, typically the pump, heating element, or control board. In many cases we replace just the failed seat component, or the seat if the board repair doesn’t pencil out. Call (888) 405-7616 for a free estimate and we’ll diagnose which it is.
Because the fill valve or flapper has worn and no longer seals, so water trickles and the tank refills itself. It’s a common, inexpensive fix: swap the worn part, confirm the supply valve and flange are sound, and the running stops. Call (888) 405-7616 and we’ll get you a written estimate.
Often yes, if your existing toilet has a standard round or elongated bowl and a nearby outlet for the seat’s power. We check the bowl shape, the mounting, and the electrical supply before recommending a seat, so it fits and functions rather than half-installing. Call (888) 405-7616 to talk through your setup.
Harder, generally. A one-piece unit hides its plumbing behind the skirt, so accessing a gasket or the trapway takes more precision than a two-piece Drake, and that labor shows up in the estimate. The parts are similar; the access isn’t. Call (888) 405-7616 for a free estimate on your specific fixture.
Vanity installation, a small bathroom remodel, and a walk-in shower or tub-to-shower conversion are the usual companions, since the toilet is already out and the floor is open. Doing them together keeps the tile and fixture work coordinated instead of scheduling it twice. Call (888) 405-7616 for a free estimate.
It depends on the service. Component repairs like a fill valve or flapper are the low end; a full bathroom remodel is the high end. These are typical estimated ranges for Garland, and the written estimate sets the final price:
| Service | Typical Estimated Range |
|---|---|
| Bathroom Vanity Installation | $800 – $3000 |
| Small Bathroom Remodel | $5000 – $12000 |
| Bathroom Remodel | $9000 – $28000 |
| Walk-In Shower Installation | $4500 – $12000 |
Call (888) 405-7616 for an exact quote. Estimates are free.
Book Your Toto Service in Garland, TX
Whether it’s a Washlet that quit spraying, a Drake that keeps running, or a full Garland bathroom built around a new Toto fixture, we’re one call from a written estimate. Free estimates, quality parts that fit Toto equipment, and work done to spec. Call (888) 405-7616. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Construction Garland.